EVO 3.3
hdmi_timings=320 1 8 30 42 238 1 4 5 16 0 0 0 60 0 6400000 1
[pi4]
# Enable DRM VC4 V3D driver on top of the dispmanx display stack
dtoverlay=vc4-fkms-v3d
max_framebuffers=2
[all]
#dtoverlay=vc4-fkms-v3d
gpu_mem_256=128
gpu_mem_512=256
gpu_mem_1024=256
[CRT-BASE]
disable_overscan=1
display_default_lcd=1
dpi_group=2
dpi_mode=87
enable_dpi_lcd=1
framebuffer_depth=32
overscan_scale=1
[CRT-SOUND]
audio_pwm_mode=3
dpi_output_format=6
dtoverlay=pwm-2chan,pin=18,func=2,pin2=19,func2=2
dtparam=audio=on
[CRT-CABLE]
crt_cable_type=1
[CRT-I2C0]
dtoverlay=i2c-gpio,i2c_gpio_sda=10,i2c_gpio_scl=11
dtparam=i2c_vc=on,i2c_vc_baudrate=1000000
[CRT-VGA666-MODE]
dtoverlay=rgb-pi
[CRT-RECOVERY]
crt_daemon_enabled=1
crt_recovery_enabled=0
crt_recovery_mode=DEFAULT
questa è la mia con lo script di bini e alla richiesta di scegliere l'uscita ho messo HDMI
# For more options and information see
#
http://rpf.io/configtxt
# Some settings may impact device functionality. See link above for details
# removes rainbow screen at boot
disable_splash=1
# removes the lightning bolt icon & console messages **use at your own risk - this will remove any warnings and could lead to SD card corruption if your power supply is faulty!!!!!!!!
#avoid_warnings=2
# uncomment if you get no picture on HDMI for a default "safe" mode
#hdmi_safe=1
# uncomment this if your display has a black border of unused pixels visible
# and your display can output without overscan
#disable_overscan=1
# uncomment the following to adjust overscan. Use positive numbers if console
# goes off screen, and negative if there is too much border
#overscan_left=16
#overscan_right=16
#overscan_top=16
#overscan_bottom=16
# uncomment to force a console size. By default it will be display's size minus
# overscan.
#framebuffer_width=1280
#framebuffer_height=720
# uncomment if hdmi display is not detected and composite is being output
hdmi_force_hotplug=1
# uncomment to force a specific HDMI mode (this will force VGA)
#hdmi_cvt=800 480 60 6
#hdmi_group=1
#hdmi_mode=1
# uncomment to force a HDMI mode rather than DVI. This can make audio work in
# DMT (computer monitor) modes
#hdmi_drive=2
# uncomment to increase signal to HDMI, if you have interference, blanking, or
# no display
#config_hdmi_boost=4
# uncomment for composite PAL
#sdtv_mode=2
#Overclocking - Proceed at your own risk!
#force_turbo=1 #Voids Warranty! (uncomment to avoid CPU scaling down)
#boot_delay=1 #helps to avoid sdcard corruption when force_turbo is enabled.
## Pi Zero 2 ##
#over_voltage=6 #needed for 1400Mhz overclock
#arm_freq=1200 #should be ok with no overvoltage
#arm_freq=1400
## Pi 3 ##
#over_voltage=2
#arm_freq=1500
# Uncomment some or all of these to enable the optional hardware interfaces
#dtparam=i2c_arm=on
#dtparam=i2s=on
#dtparam=spi=on
# Uncomment this to enable infrared communication.
#dtoverlay=gpio-ir,gpio_pin=17
#dtoverlay=gpio-ir-tx,gpio_pin=18
# Additional overlays and parameters are documented /boot/overlays/README
# Enable audio (loads snd_bcm2835)
dtparam=audio=on
[pi4]
# Enable DRM VC4 V3D driver on top of the dispmanx display stack
#dtoverlay=vc4-fkms-v3d
#max_framebuffers=2
[all]
#dtoverlay=vc4-fkms-v3d
gpu_mem_256=128
gpu_mem_512=256
gpu_mem_1024=256
overscan_scale=1
dtparam=i2c_vc=on
##audio_pwm_mode=3
##dtoverlay=pwm-2chan,pin=18,func=2,pin2=19,func2=2
##disable_audio_dither=1
#dtoverlay=vga666,mode6
#enable_dpi_lcd=1
#display_default_lcd=1
#dpi_output_format=6
#dpi_group=2
#dpi_mode=9
#hdmi_timings=480 1 14 45 56 300 1 10 5 5 0 0 0 60 0 9600000 1
#HDMI
dtoverlay=act-led,gpio=27,activelow=on
gpio=26=op,dl
